Mastering Basic Plumbing When You Install a Bathtub
Mastering Basic Plumbing When You Install a Bathtub
Blog Article
Just how do you feel on the subject of Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately difficult project. If the old bathtub is easily easily accessible, the task can relocate speedily; if you need to open a wall to remove the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. See to it you have actually qualified on your own for the work and are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your bathroom if you have already gotten a brand-new bathtub as well as don't require to change the arrangement of your previous water supply pipes.
Your devices and also material list must consist of the following:
Preparing for the Installation
Firstly, the sustaining framework provided with the bath should be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipes. Once the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the bath tub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the tub until the spirit level reviews level.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water and inspect all joints and also brand-new pipework for leakages and tighten them if needed. Fill the bath tub as well as likewise check the overflow outlet and the typical electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bathtub must wait till the bath tub has actually been made use of at the very least when as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Secure the faucet in place with the producer supplied backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind must be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture an inflexible seal, causing the water to penetrate the wall surface between the bath as well as the tiling, resulting in difficulties with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader on Installing A Bathtub, I think sharing that piece of content was beneficial. Sharing is caring. You won't know, you could be doing someone a favor. I am grateful for your time. Come back soon.
Connect for quality. Report this page